Fortinet NSE7_SDW-7.2 Certification Exam Sample Questions and Answers

NSE 7 SD-WAN Dumps, NSE7_SDW-7.2 Dumps, Fortinet NSE 7 SD-WAN PDF, NSE7_SDW-7.2 PDF, NSE 7 SD-WAN VCE, Fortinet NSE 7 SD-WAN Questions PDF, Fortinet Exam VCE, Fortinet NSE7_SDW-7.2 VCE, NSE 7 SD-WAN Cheat SheetBefore you write the Fortinet NSE 7 SD-WAN (NSE7_SDW-7.2) certification exam, you may have certain doubts in your mind regarding the pattern of the test, the types of questions asked in it, the difficulty level of the questions and time required to complete the questions. These Fortinet Certified Solution Specialist - Network Security (NSE 7 SD-WAN) sample questions and demo exam help you in removing these doubts and prepare you to take the test.

The best approach to pass your Fortinet NSE7_SDW-7.2 exam is to challenge and improve your knowledge. To test your learning and identify improvement areas with actual exam format, we suggest you practice with Premium Fortinet NSE7_SDW-7.2 Certification Practice Exam. The practice test is one of the most important elements of your Fortinet NSE 7 - SD-WAN 7.2 (NSE 7 SD-WAN) exam study strategy to discover your strengths and weaknesses, to improve your time management skills and to get an idea of the score you can expect.

Fortinet NSE7_SDW-7.2 (NSE 7 SD-WAN) Sample Questions:

01. What does forward error correction do?
a) It sends the same packets across multiple links.
b) It buffers packets and transmits them at the appropriate speed.
c) It reorders packets at the destination.
d) It generates parity packets with redundant data.
 
02. In which rule strategy are cost and interface preference not considered selection factors?
a) Best Quality
b) Lowest Cost (SLA)
c) Maximize Bandwidth (SLA)
d) Manual
 
03. An administrator configured a best quality SD-WAN rule with WAN1 and WAN2 as members. WAN1 has the highest configuration priority, and link-cost-threshold is set to 10. FortiGate reports a latency of 100 ms and 120 ms for WAN1 and WAN2, respectively.
Which change in the measured latency will make WAN2 the new preferred member?
a) When WAN2 has a latency lower than ~91 ms
b) When WAN1 has a latency lower than 100 ms
c) When WAN1 has a latency of 120 ms
d) When WAN2 has a latency of 100 ms
 
04. Which two features are supported by IKEv2 and not by IKEv1?
(Choose two.)
a) Asymmetric authentication
b) IKE mode configuration
c) IKE aggressive mode
d) Network overlay ID
 
05. By default, what member information does FortiGate consider when selecting the best member in a lowest cost (SLA) SD-WAN rule?
a) Status of configured SLA targets, cost, and priority
b) Status of configured SLA targets, interface index number, and priority
c) Interface index number, cost, and priority
d) Status of configured SLA targets, cost, and corrected metric
 
06. In an SD-WAN rule, which setting enables you to skip the best-route check for SD-WAN rule matching?
a) default
b) link-cost-threshold
c) tie-break
d) gateway
 
07. When is an SD-WAN member considered to be in the dead state?
a) When both servers used for health checks are reachable by an interface member
b) When the SD-WAN member reaches the failure threshold
c) When the SD-WAN member has an active route in a routing table
d) When the SD-WAN member meets the SLA target requirement
 
08. If the outgoing interface for an established SNATed session changes, which two requirements must the configuration meet so that FortiGate continues forwarding packets from that session to the new outgoing interface?
(Choose two.)
a) You must have a firewall policy that accepts the new traffic flow for the session.
b) You must configure FortiGate so the SNAT IP address doesn’t change.
c) You must enable the snat-route-change setting.
d) You must set firewall-session-dirty to check-new on the new matching firewall policy.
 
09. Which session flag indicates the ID of the matching SD-WAN member?
a) serial
b) sdwan_service_id
c) sdwan_mbr_seq
d) policy_id
 
10. In a spoke IPsec phase 1 configuration, which setting must be enabled in order for the spoke to participate in ADVPN?
a) auto-discovery-sender
b) auto-discovery-receiver
c) auto-discovery-shortcuts
d) auto-discovery-forwarder

Solutions:

Question: 01

Answer: d

Question: 02

Answer: c

Question: 03

Answer: a

Question: 04

Answer: a, d

Question: 05

Answer: a

Question: 06

Answer: a

Question: 07

Answer: b

Question: 08

Answer: a, b

Question: 09

Answer: c

Question: 10

Answer: b

Note: If you find any error in these Fortinet NSE 7 - SD-WAN 7.2 (NSE 7 SD-WAN) sample questions, you can update us by write an email on feedback@nwexam.com.

Rating: 4.9 / 5 (83 votes)